Over the last several years, the number of threads on forums regarding axe and hatchet re-profiling have increased. Some of these contain useful info, most though talk about it, but never show how it's actually done. Even fewer still explain why it makes an axe cut better and how the profile differs between an axe for softwood, and an axe for hardwood. Changing the edge geometry of an axe is NOT reprofiling the axe. This is merely sharpening the axe. Anyone who tries to tell you differently is trying to sell a story to make themselves look more knowledgable than they actually are.
I initially became interested in reprofiling axes about 4 years ago. I had always been keen to learn this black art because as a child I had been to country fairs in Queensland where I witnessed axe racing. It is something special to see one of these axes slice through a large block of wood like butter. I was always impressed at the large chunks of wood these axes managed to throw and knew there was something special about them. When compared to a regular axe, they had a different shape, profile and were highly polished. I always knew this was no coincidence.
Why reprofile an axe?
It seems like an axe should be able to perform properly straight from the box right? I mean we don't need to reprofile knives. The truth is that most axe companies forge the heads, then look at the cheapest and easiest option. This usually involves leaving the bit of the axe thick. this is done so that the heat treat is easier and cheaper steel can be used. You see, the finer the edge, the more necessary quality steel and heat treat becomes. Axes need to be left reasonably thick at the bit because heat treating thin metal is very difficult. Once the heat treat is done, they should then be ground and polished so that the profile is correct, and the edge geometry is right. Unfortunately, to cut down on work all the smith does is put the edge on a belt grinder and gives it a very obtuse edge and then call it a "convex edge". At this point it would pay to look at the following diagram:
If you look where the cheeks are, these should also be hollowed out. If they are not, then the axe will bind due to friction when you try to take deep cuts. This is a tricky thing to do correctly though. When the bit initially cuts in, the wood compresses. As the bit continues to cut in, the wood ramps up on the wedge shape of the bit, then it reaches the cheeks. At this point the wood loses contact with axe, allowing the momentum of the axe to drive the bit in deeper without the wood slowing it at the cheeks. Wood is elastic to a point, and when it passes the union of the bit / cheeks, it decompresses slightly. When hollowing out the cheeks, you need to make sure you hollow it out enough so when the wood decompresses, it does not bind at the cheeks. The following rudimentary diagram illustrates the point:
Difference between hardwood and softwood axes
There is a difference between axes meant for hardwood as opposed to softwood. Softwood is more "spongy" in a sense, so when you make your second cut, you need a wider blade to clear the cut and eject the chip of wood out. This does not mean thicker, but, from the edge to where the cheeks start will be a greater distance than on a hardwood axe. I typically make this distance anywhere up to 1 1/2" on axes used for birch or pine. If the blade is narrow, then the wood will simply compress and not split along the grain. This results in having to twist the axe in the wood to try clear the cut. Hardwoods are more brittle so you don't need such a broad "wedge" to cause the wood to crack and be ejected. On hardwoods I tend to leave about a 1/2" blade.
Lets reprofile an axe
So what tools do we need? Here is a list:
1) Angle grinder with grinding disk.
2) Flap disks ranging from 60 - 120 grit.
3) Drill with paint stripping wheel.
4) Bucket of water or snow. I prefer snow.
5) Sanding pads.
6) A belt grinder is preferrable but not absolutely necessary.
7) Quick clamps
8) Bastard file and tape
9) Ear and eye protection
10) Straight edge
Now lets see what we have to work with. As you can see it's a pretty standard Wetterlings axe. It has the forged finish and rough look to it. I hand selected this one as it had the least deformed and unbalanced head of the lot. This is not saying much for the quality control.
Once the axe is laid on the table and a straight edge is used, you soon see how bad the transition between the cheeks and the eye actually is.
What we need to do is thin down the bit so we have a chisel grind instead of an obtuse convex first. Then hollow out the cheeks, being mindful to blend them in to the eye and poll. Here is a side view where the dent from the smith's hammer is evident between the poll and cheeks.
If you use a file, you can set up your axe like in the following picture.
Once you have the blade of the axe ground so that the convex edge is gone, you can assess how unbalanced the axe is. This is what I was left with.
Now we move onto hollowing out the cheeks. The first step is to make bumpers to stop us running the angle grinder to close to the edge. I do this by finding a scrap piece of laminate.
Now one side has been blended, repeat the process on the other side.
This side looks good, now it's time to do the other. Keep checking that the work is symmetrical. Once done, give the head a final polish with the sanding blocks / pads. Give the edge a final sharpen, eliminating the wire edge you got from the grinder or files. You will be left with this:
As you can see, the profile looks much better and the transition from cheek to poll is smooth. The edge is also thinner, which will prevent deflection if you chop at shallower angles. The only recommendation now are that you put a very small convex or secondary bevel on the edge to prevent chipping. Also, work harden the edge before use by lightly chopping some wood after you have sharpened it. If cutting in cold weather, put the head under your jacket to warm it first before you start cutting otherwise you can also damage the edge. this is good practice with any axe, not just one that has been re-profiled. Any questions or comments are welcome.