Garage

Thursday 3 March 2011

How to reprofile axes and hatchets

Over the last several years, the number of threads on forums regarding axe and hatchet re-profiling have increased. Some of these contain useful info, most though talk about it, but never show how it's actually done. Even fewer still explain why it makes an axe cut better and how the profile differs between an axe for softwood, and an axe for hardwood. Changing the edge geometry of an axe is NOT reprofiling the axe. This is merely sharpening the axe. Anyone who tries to tell you differently is trying to sell a story to make themselves look more knowledgable than they actually are.

I initially became interested in reprofiling axes about 4 years ago. I had always been keen to learn this black art because as a child I had been to country fairs in Queensland where I witnessed axe racing. It is something special to see one of these axes slice through a large block of wood like butter. I was always impressed at the large chunks of wood these axes managed to throw and knew there was something special about them. When compared to a regular axe, they had a different shape, profile and were highly polished. I always knew this was no coincidence.

Why reprofile an axe?
It seems like an axe should be able to perform properly straight from the box right? I mean we don't need to reprofile knives. The truth is that most axe companies forge the heads, then look at the cheapest and easiest option. This usually involves leaving the bit of the axe thick. this is done so that the heat treat is easier and cheaper steel can be used. You see, the finer the edge, the more necessary quality steel and heat treat becomes. Axes need to be left reasonably thick at the bit because heat treating thin metal is very difficult. Once the heat treat is done, they should then be ground and polished so that the profile is correct, and the edge geometry is right. Unfortunately, to cut down on work all the smith does is put the edge on a belt grinder and gives it a very obtuse edge and then call it a "convex edge". At this point it would pay to look at the following diagram:


If you look where the cheeks are, these should also be hollowed out. If they are not, then the axe will bind due to friction when you try to take deep cuts. This is a tricky thing to do correctly though. When the bit initially cuts in, the wood compresses. As the bit continues to cut in, the wood ramps up on the wedge shape of the bit, then it reaches the cheeks. At this point the wood loses contact with axe, allowing the momentum of the axe to drive the bit in deeper without the wood slowing it at the cheeks. Wood is elastic to a point, and when it passes the union of the bit / cheeks, it decompresses slightly. When hollowing out the cheeks, you need to make sure you hollow it out enough so when the wood decompresses, it does not bind at the cheeks. The following rudimentary diagram illustrates the point:

This diagram is a top down view of an axe head. many start out like the axe on the left. After a reprofile, they look like the axe on the right. The transition between the cheeks and the eye MUST be smooth. If it isn't you will have binding occuring at this point when you try to split wood.

Difference between hardwood and softwood axes
There is a difference between axes meant for hardwood as opposed to softwood. Softwood is more "spongy" in a sense, so when you make your second cut, you need a wider blade to clear the cut and eject the chip of wood out. This does not mean thicker, but, from the edge to where the cheeks start will be a greater distance than on a hardwood axe. I typically make this distance anywhere up to 1 1/2" on axes used for birch or pine. If the blade is narrow, then the wood will simply compress and not split along the grain. This results in having to twist the axe in the wood to try clear the cut. Hardwoods are more brittle so you don't need such a broad "wedge" to cause the wood to crack and be ejected. On hardwoods I tend to leave about a 1/2" blade.

Lets reprofile an axe
So what tools do we need? Here is a list:

1) Angle grinder with grinding disk.
2) Flap disks ranging from 60 - 120 grit.
3) Drill with paint stripping wheel.
4) Bucket of water or snow. I prefer snow.
5) Sanding pads.
6) A belt grinder is preferrable but not absolutely necessary.
7) Quick clamps
8) Bastard file and tape
9) Ear and eye protection
10) Straight edge

Now lets see what we have to work with. As you can see it's a pretty standard Wetterlings axe. It has the forged finish and rough look to it. I hand selected this one as it had the least deformed and unbalanced head of the lot. This is not saying much for the quality control.



Once the axe is laid on the table and a straight edge is used, you soon see how bad the transition between the cheeks and the eye actually is.



What we need to do is thin down the bit so we have a chisel grind instead of an obtuse convex first. Then hollow out the cheeks, being mindful to blend them in to the eye and poll. Here is a side view where the dent from the smith's hammer is evident between the poll and cheeks.




This is where you even up each side of the blade. Manufacturers like to boast a "convex" edge. This is usually a rounded edge that has been convexed to hide the poor edge geometry and inconsistancy. We need to take away the very obtuse convex until we have a "scandi" grind. We can do this with files, or use a belt grinder. I have made a cheap and nasty rig for my grinder that the poll can rest on while the blade is ground flat.

If you use a file, you can set up your axe like in the following picture.
The tape will protect the poll as you draw file. If you have a belt grinder, you need to make a jig so that the poll is raised off the belt slightly so that you can grind the blade of the axe. I don't have a picture of this but I just use vice grips and a piece of angle iron on my grinder. Remember to cool the metal REGULARLY!!

Once you have the blade of the axe ground so that the convex edge is gone, you can assess how unbalanced the axe is. This is what I was left with.



As you can see, the top picture shows that there is much more meat on that cheek than on the other side. We need to make it symmetrical.

Now we move onto hollowing out the cheeks. The first step is to make bumpers to stop us running the angle grinder to close to the edge. I do this by finding a scrap piece of laminate.
Placing the edge onto the laminate, trace around the edge and then grind it out with the angle grinder or bench grinder.

Now clamp your axe to the bench using quick clamps. Measure a half inch from the edge and clamp the bumper onto the blade. Now with the angle grinder, carefully blend the poll with the cheeks. This stage is critical. Constantly check the progress and how much has been removed. You won't grind all the way up to the bumper, so 1/2" will translate to about an inch when it's done.

At this point it is very easy to overheat the head. Keep cooling it. Once one side looks good, go to the belt grinder or the paint stripping wheel on the drill. Starting from the poll, grind down to the edge to smooth out and polish out grind marks. REMEMBER, you will need to reverse the drill's spin depending on the edge you are grinding against. If you don't, it will grab and you will injure yourself. Once you have an even finish, inspect the axe in a good light.
Now one side has been blended, repeat the process on the other side.


This side looks good, now it's time to do the other. Keep checking that the work is symmetrical. Once done, give the head a final polish with the sanding blocks / pads. Give the edge a final sharpen, eliminating the wire edge you got from the grinder or files. You will be left with this:


As you can see, the profile looks much better and the transition from cheek to poll is smooth. The edge is also thinner, which will prevent deflection if you chop at shallower angles. The only recommendation now are that you put a very small convex or secondary bevel on the edge to prevent chipping. Also, work harden the edge before use by lightly chopping some wood after you have sharpened it. If cutting in cold weather, put the head under your jacket to warm it first before you start cutting otherwise you can also damage the edge. this is good practice with any axe, not just one that has been re-profiled. Any questions or comments are welcome.

35 comments:

  1. Nicely done, and clearly explained. Thank you!

    ReplyDelete
  2. Actually, some knives do get reprofiled out of the box. Some will do it themselves and some will send them out to people like Richard J on bladeforums or Tom Krein.

    ReplyDelete
  3. Knives come down to personal preferance for an edge geometry, rather than proper functioning of the implement. If the knife that you spent 50 - 100 dollars on came with an edge that was as dangerous to use as an overly obtuse convex and full cheeks on an axe, then by all means it requires a reprofile. For the most part though, this is not necessary. Plus, the choice of knives with any edge geometry or profile you want is much broader than that of a well profiled axe.

    ReplyDelete
  4. This comment has been removed by the author.

    ReplyDelete
  5. Great blog! I recently installed a wood stove and now I am looking at axes to buy. Do you have a style of handle or weight that you would recommend? Thanks!

    ReplyDelete
  6. I would like to subscribe. I like your post on how to profile an axe. Well done!!!
    David axeoexa Australia

    ReplyDelete
  7. This comment has been removed by the author.

    ReplyDelete
    Replies
    1. Hello Michiel, I don't have any experience with Gransfors axes but I do with Wetterlings which are similar. It is the bit that I believe makes the biggest impact on how the axe cuts woods. Softwood axes should have a bit or sharpened section that is more exaggerated than a hard wood axe. This needs to act like a chisel that will compress the softwood until it cannot compress anymore forcing the chip to pop out.

      Delete
  8. Do you have to re-harden the steel once you re-profile it?

    ReplyDelete
    Replies
    1. No rehardening is needed providing you don't overheat the steel. Be very careful when grinding and polishing and keep the metal cold with a water soaked sponge.

      Delete
  9. Thanks very much for this informative site. I've just purchased from the local Red Shield shop a very old hatchet and was wondering how to correctly sharpen and re-shape the bit. This will be very helpful.

    ReplyDelete
  10. Hi just found this article--timely for me as I purchased a wetterlings carpenter's axe that is off angle 9 deg from center, and twisted as well. I am not sure it if is worth doing all this but since it is discontinued now don't know what to do with it. I wanted it for wood carving not chopping or splitting, and the angle off is on the wrong hand it is almost a left handed flat axe. Any ideas? Thanks.

    ReplyDelete
  11. The best post.
    Thanks for share this article.
    I look forward to your new article.
    this post

    ReplyDelete
  12. I am a Norwegian now living in Australia, found your site looking for advice on how to profile an axe I am forging. Good site!
    Bjorn

    ReplyDelete
  13. I found your this post while searching for information about blog-related research ... It's a good post .. keep posting and updating information. best-battle-throwing-axes-for-beginners

    ReplyDelete
  14. Hi Axeman
    I like it really! Thanks! I can’t wait to share this to my friend. Great! looking forward to read your next posts.
    Check toolsbeat for learn more about our product reviews

    ReplyDelete
  15. Great things put in this blog, thank you so much for sharing with us this informative blog. Visit Ogen Infosystem to get creative and responsive website designing services.
    PPC Company in Delhi

    ReplyDelete
  16. Amazing blog, thank you so much for sharing with us. Get the best Shipping Services by Y&H Cargo India.
    Shipping Company in India

    ReplyDelete
  17. Nice Information presented you by this blog, thank you so much for sharing this informative blog. Visit for Mutual Find Schemes and Advisors.
    Best Performing Mutual Fund

    ReplyDelete
  18. Nice Blog, Visit for the daily lifestyle activities and about Health, Wealth and Lifestyle Events by Lifestyle Magazine in India.
    Lifestyle Magazine India

    ReplyDelete
  19. Visit for the Commercial Vehicle Wrap and Vinyl Signage Printing Services by Kalakutir Pvt Ltd.
    Vinyl Signage Printing

    ReplyDelete
  20. I might suggest solely beneficial in addition to trusted facts, and so find it: Try reading this for more info

    ReplyDelete
  21. putlocker Are you looking for a web development company? Oliveasia.com Pte Ltd is one of the best web development company in Singapore that provide the best website design services in Singapore, contact us - +65 6483 7635

    ReplyDelete
  22. The best website designing company in Delhi is Online Front, which provide services like creative designs and Web designing etc. By using the different skills. We will provide you the best design for your online store. Do you know why we design interactive and responsive websites for you? Because , website is your first impression on your prospective customer. That’s why the best website design is important for making your online store as a brand.
    Visit:-


    Website Designing Company in Delhi
    Digital Marketing Agency in Delhi
    Website Design Company in Delhi
    Buy Website Packages in Delhi
    Search Engine Optimization(SEO) Services Provider in Delhi
    Local SEO Services Provider in Delhi

    Visit Our Partner’s Site:-

    Gas Stove Repair & Services in Delhi
    B2B Marketplace in Delhi
    Satta King

    ReplyDelete
  23. Replies

    1. Hello
      Please i just took up macaw breeding as a hobby after my mom passed away because they were her favorite birds. Despite the fact that they are very intelligent, am finding it very difficult getting them to mate.
      For any information CLICK HERE http://supremeparrotfarm.company.com/ we shall get back to you. contact-about-us. THANKS

      Delete

  24. Hello
    Please i just took up LABRADOR PUPPIES breeding as a hobby after my mom passed away because they were her favorite PUPPIES. Despite the fact that they are very intelligent, am finding it very difficult getting them to mate.
    For any information CLICK HERE LABRADOR PUPPIES FOR SALE. THANKS

    ReplyDelete
  25. Exceptional Blog! Generally I don’t read post on blogs, but I wish to say that this write-up very compelled me to try and do so! Your writing style has been surprised me. Thanks, very nice post.
    Regards : Sankey Diagram. Look at my articles and share your feedback : Read more here.

    ReplyDelete
  26. Not that I am complaining, but slow loading instances times will sometimes affect your placement in google and could damage your high-quality score if advertising and marketing with AdWords. Well I am adding this RSS to my e-mail and can look out for a lot more of your respective fascinating content.

    야동

    ReplyDelete
  27. You are my inhalation, I have few web logs and very sporadically run out from to post .

    외국인출장

    ReplyDelete
  28. Reading your article made it easy for me to understand. I would like to see more articles as you describe. An e visa Turkey can be applied for online without a hassle and it saves time and more at the same time.

    ReplyDelete